2W1ETN

Obtaining the ADSL Sync speed from your Cisco Router is quite easy, just pass the following command

You’ll get something like the following back:

router#show dsl interface atm0

ATM0

Alcatel 20150 chipset information

                ATU-R (DS)                      ATU-C (US)

Modem Status:    Showtime (DMTDSL_SHOWTIME)

DSL Mode:        ITU G.992.1 (G.DMT) Annex A

ITU STD NUM:     0x01                            0x1

Vendor ID:       'ALCB'                          'TSTC'

Vendor Specific: 0x0000                          0x0000

Vendor Country:  0x00                            0xB5

Capacity Used:   100%                            62%

Noise Margin:     5.5 dB                         19.0 dB

Output Power:    20.0 dBm                        12.0 dBm

Attenuation:     49.0 dB                         22.5 dB

Defect Status:   None                            None

Last Fail Code:  None

Selftest Result: 0x00

Subfunction:     0x15

Interrupts:      1333 (0 spurious)

PHY Access Err:  0

Activations:     1

LED Status:      ON

LED On Time:     100

LED Off Time:    100

Init FW:         embedded

Operation FW:    embedded

SW Version:      3.8131

FW Version:      0x1A04

                 Interleave             Fast    Interleave              Fast

Speed (kbps):          5856                0           448                 0

Cells:                15473                0        192329                 0

Reed-Solomon EC:       7248                0             0                 0

CRC Errors:               3                0             0                 0

Header Errors:            2                0             0                 0

Bit Errors:               0                0

BER Valid sec:            0                0

BER Invalid sec:          0                0

LOM Monitoring : Disabled

DMT Bits Per Bin

00: 0 0 0 0 0 0 0 4 4 5 7 8 8 9 9 8

10: 8 8 8 8 8 7 7 7 6 6 5 5 4 3 0 0

20: 0 0 0 0 0 0 4 5 5 6 7 8 9 9 A A

30: A B B B C C C D D D D D D D D D

40: 0 D D D D D D D 2 D D D D D D D

50: D D C D D C C C C D D D D C D D

60: D C C C C C C C C C C C C B 8 B

70: C C B C C C C C C C C C C B B B

80: B B B A B B A A A A A A A A 8 A

90: A 9 9 9 9 9 9 9 8 7 8 8 8 8 8 7

A0: 7 5 7 7 7 5 7 8 8 8 8 8 8 8 7 7

B0: 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 5

C0: 5 5 5 5 5 4 4 4 4 4 2 2 0 0 0 0

D0: 0 0 0 0 0 0 2 2 2 2 3 3 2 4 4 4

E0: 4 4 4 4 4 4 4 4 4 4 3 4 3 3 3 3

F0: 3 3 3 2 2 0 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

Enabling the HTTP server on Cisco Routers is easily done using the console port or via an SSH connection.

You might wonder why you’d want the HTTP server running; well you need it if you want to install SDM (Cisco Router and Security Device Manager)

To enable the web server logon or connect via terminal

Then type the command

enable

Then type

config

Press enter to config from the terminal when prompted

You should see a prompt like (Which is the config prompt):

Router(config)#

Enter the following commands

ip http server
ip http secure-server
ip http authentication local

If you intend to install SDM or want to be able to access the router from SSH then you need to add a user account as below:

Username sdm privilege 15 password 0 sdm

That will create a user with the username and password of SDM

If you haven’t enabled SSH and or telnet do so using the following commands:
line vty 0 4
login local
transport input telnet ssh